Daikin Alarm Code (last refer manual 'F,G,H,J')

Read Term And Condition Before Use This Application !!!

F101	High pressure switch (HPS) is open   If HPS is opened before compressor starts   Fuse (FU1) is open   Faulty controller
F109	LPT drops below –90kPa within 2seconds after compressor starts to operate
F111	A communication error in the CPU and I/O board
F301	Temperature setting request
F401	Air temperature sensors [SS][DSS][RS] failure Air temperature sensors [RS][DRS-optional][SS] failure
F403	Air temperature sensors [RS][DRS-optional][SS] failure
F603	Suction modulation valve [SMV] failure Incorrect controller model setting
F701	Main power is greater than 535V or less than 300V within 2seconds during unit start Main power frequency abnormality
F705	S phase is open
F803	If any of the following conditions apply Compressor magnetic switch arcing / Connector of compressor disconnected Failures are present in any 2 of HPT sensor, LPT sensor and DCHS sensor E107 is generated twice due to EV opening error
E101	High pressure switch (HPS) is open during normal operation
E103	Compressor operating current is high (electronic type OC)
E105	Compressor operating current is high (microcomputer type OC)
E107	The discharge gas temperature is excessively high Refrigerant shortage is detected (EV opening large)
E109	Low pressure stays at –90kPa or less for 2 seconds during normal operation Low pressure stays at 400kPa or higher for 5 minutes
E201	Pump down is not completed within 120 seconds
E203	Overcooling prevention (Supply sensor is less –3 degree C below Set Point) continues for 3 minutes in the chilled mode If supply sensor 0.5 degree C lower than set point for 30 minutes in chilled mode
E207	Defrosting is not completed within 100 minutes
E303	Humidity setting request / dHU is set to ON when REHEAT set to OFF
E305	Defrost timer setting request
E307	Calendar setting request
E311	Trip start setting request
E315	PT/CT board failure
E401	Supply air temperature sensor (SS) fault
E402	??Data recorder supply air temperature sensor (DSS) fault
E403	Return temperature air sensor (RS) fault
E404	Data recorder return air sensor (DRS optional) fault
E405	Discharge gas temperature sensor (DCHS) fault
E406	Suction gas temperature sensor (SGS) fault
E407	Evaporator inlet pipe temperature sensor (EIS) fault
E409	Evaporator outlet pipe temperature sensor (EOS) fault
E411	Ambient temperature sensor (AMBS) fault
E413	Low pressure sensor (LPT) fault
E415	High pressure sensor (HPT) fault
E417	Voltage sensor (PT1) fault
E421	Current sensor (CT1) fault
E423	Current sensor (CT2) fault
E425	USDA sensor (USDA1 optional) fault
E427	USDA sensor (USDA2 optional) fault
E429	USDA sensor (USDA3 optional) fault
E431	Humidity sensor (HuS optional) fault
E433	Cargo temperature sensor (CTS optional) fault
E603	Suction modulating valve (SMV) wiring fault, drive circuit fault or controller setting error
E607	Contact point of manual defrost key (key pad) faulty
E707	Instantaneous voltage failure shutdown Power supply voltage failure shutdown during operation (greater than 535V, less than 334V)
E801	CPU board battery failure
E805	FA sensor failure Initial setting [FA SEN] is set incorrectly.
E807	The ventilator is opened during frozen operation mode
J161	Evaporator fan failure
J051	Compressor malfunction
J061	Abnormal OFF value
J062	Not recovered (Not reset)
J064	High pressure does not rise.
J065	High pressure does not drop.
J081	Long pump-down
J101	Valve leakage
J121	Sensor deterioration
J141	Sensor deterioration
J161	Evaporator fan motor malfunction
J201	Economizer solenoid valve malfunction
J221	Discharge gas bypass solenoid valve malfunction
J281	Suction modulating valve does not activate
J291	Long pump-down
J301	Injection solenoid valve malfunction
J321	Hot-gas solenoid valve malfunction
J322	Reheat coil solenoid valve malfunction
J501	Out of ambient temperature conditions
J502	Long pull-down time
J701	Out of starting conditions
J702	Long defrosting time
J801	Long pull-down time
E672	Open or short circuit
E678	Open or short circuit
E679	No ON signal detected from DCF1
E680	No ON signal detected from DCF2
J421	Pressure increase and no current detected
J422	No pressure increase & no lock current detected
J423	No pressure increase & lock current detected
J424	O2 check valve (OCV) is open but no fluctuations in O2 concentration
J425	O2 purge valve (OPV) is open but no increase in O2 concentration
J426	Control valve (CTV1) is open but pressure does not change
J427	Control valve (CTV2) is open but pressure does not change
J428	O2 main discharge valve (ODV) is open but pressure does not change
J429	O2 bypass valve (OBV) is open but pressure does not change
J42A	Purge valve (PGV) is open but pressure does not change
J441	O2 concentration is higher than appropriate range
J442	O2 concentration is lower than appropriate range
J443	Intake air temperature is outside judgment temperature range
J444	Output voltage is outside appropriate range
J445	Calibration error (cannot be saved)
J461	Drop in O2 concentration is less than 5%
J462	O2 concentration does not reach 8% or lower
F315	F315 PT/CT board failure
F405, F407, F409	Pressure sensor
F805	Compressor magnetic switch arcing
F807	Compressor connection disconnected
F809	Click here for details
E419, E417, E421, E423	Click here for more details
E809	Refrigerant shortage is detected (EV opening large) (DECOS-3h and later settings)
E205	Handling of the Alarm E205 (F801)
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
xxx	xxx
XX	XX
XX	XX
XX	XX